manualshive.com logo in svg

Kontron CP3010-SA, Руководство пользователя

Поделиться
Скачать
Kontron CP3010-SA Скачать руководство пользователя страница 24

D R A F T   —   F O R   I N 

T E R N A L   U S E   O N L Y

24

www.kontron.com

User Guide

CP3010-SA

2.5.2   SATA Flash

For flexible flash extension, the CP3010-SA provides either a CFast socket, J5, for a SATA 3Gb/s CFast
memory card, or up to 64 GB soldered SLC-based NAND flash memory with built-in full hard disk emu-
lation, up to 60 MB/s read rate, and up to 55 MB/s write rate.

Note:

Write protection is available for both the CFast card and the soldered NAND flash. Please 
contact Kontron for further assistance if write protection is required.

2.6   Trusted Platform Module 1.2

The CP3010-SA supports the Trusted Platform Module (TPM) 1.2. TPM1.2 is a security chip specifically
designed to provide enhanced hardware- and software-based data and system security. TPM1.2 is
based on the Atmel AT97SC3204 security controller and stores sensitive data such as encryption and
signature keys, certificates and passwords, and is able to withstand software attacks to protect the
stored information.

2.7   Board Inter faces

2.7.1   Front Panel LEDs

The CP3010-SA provides two system status LEDs, one temperature status LED (TH LED) and one Watch-
dog status LED (WD LED), as well as four General Purpose/POST code LEDs (LED3..0). Their functionality
is described in the following chapters and reflected in the registers mentioned in Chapter 3, Configu-
ration. 

2.7.1.1   System Status LEDs

Note:

If the TH LED flashes red at regular intervals, it indicates that the processor junction tem-
perature has reached a level beyond which permanent silicon damage may occur and the
processor has been shut off. To return to normal operation, the power must be switched
off and then on again.

Table 7: System Status LEDs Function

LED

COLOR

STATE

FUNCTION

TH LED

red / green

Off

Power failure

Green

Board in normal operation

Red

CPU operating temperature has exceeded its defined operating limit

Red blinks

CPU temperature above 110°C (CPU has been shut off)
In this event, all General Purpose LEDs (LED3..0) are blinking red as well.

WD LED

red / green

OFF

Watchdog inactive

Green

Watchdog active, waiting to be triggered

Red

Watchdog expired

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды