Kontron CP3010-SA Скачать руководство пользователя | Manualshive

Страница: 33 / 80

background image

D R A F T — F O R I N

T E R N A L U S E O N L Y

33

www.kontron.com

User Guide

CP3010-SA

2.7.9.3 Optional Rear I/O Interface

The CP3010-SA board provides optional rear I/O connectivity for peripherals. When the rear I/O mod-
ule is used, the signals of some of the main board / front panel connectors are routed to the rear I/O
module interface.

The CP3010-SA with rear I/O is compatible with all standard 3U CompactPCI passive backplanes with
rear I/O support.

Note:

To support the rear I/O feature, a 3U CompactPCI backplane with rear I/O support is re-
quired. Do not plug a rear I/O configured board in a backplane without rear I/O support.
Failure to comply with the above will result in damage to your board.

The CP3010-SA rear I/O provides the following interfaces (all signals are available on J2 only if the
board is ordered with rear I/O functionality):

»

Two USB 2.0 ports

»

Two Gigabit Ethernet ports without LED signals

»

Two SATA ports

»

COMA and COMB, or COMA and GPIO (all ports have 3.3V LVTTL signaling)

»

General purpose signals: 5 x GPIs and 3 x GPOs

»

VGA analog port

»

Management and control signals

»

System write protection

»

Input for +5V standby power

»

Geographic addressing (GA[4..0])

Note:

The pinout of the rear I/O CompactPCI connector on the CP3010-SA is compatible with that
of the CP305, CP307, CP308, and CP3002. Thus, rear I/O modules designed for these
boards can also be used with the CP3010-SA.

«
...
31
32
33
34
35
...
»

Содержание CP3010-SA

















































































Отзывы:

Нет отзывов

Похожие инструкции для CP3010-SA

Бренд: Xilinx Страницы: 48

T15 Mifare Reader Black

Бренд: Gallagher Страницы: 13

Бренд: Rastergraf Страницы: 169

Sentinel-Prox DC-1023

Бренд: AWID Страницы: 12

Бренд: Handpoint Страницы: 36

Бренд: Advantech Страницы: 38

Бренд: Roger Страницы: 7

Бренд: Planet Страницы: 41

SwapBox Classic

Бренд: SCM Страницы: 78

Бренд: Contec Страницы: 5

Бренд: ERMA Страницы: 28

Бренд: Novatel Страницы: 208

Бренд: Diablotek Страницы: 1

Бренд: Star Micronics Страницы: 66

Бренд: Naigon Electronics Страницы: 42

THINGMAGIC SARGAS

Бренд: Jadac Страницы: 59

Бренд: Digitus Страницы: 4

Бренд: FEITIAN Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды