manualshive.com logo in svg

Koden CVS-875D, Руководство по установке

Поделиться
Скачать
Koden CVS-875D Скачать руководство пользователя страница 81

CVS-875D/877D   

 

Chapter 1 Installation

 

0092607072-01 

 

1-59 

1.7  Connection  of  Hemisphere  V102/V104s/V200s  GPS  Compass  / 

ComNav Vector G1 GPS Satellite Compass                                                                                                 

 
This  is  to  describe  the  connection  of  Hemisphere  V102/V104s/V200s  GPS  Compass  / 
ComNav Vector G1 GPS Satellite Compass used as GPS compass and Heaving sensor. 
Refer  to  the  installation  manual  of  the  Hemisphere  V102/V104s/V200s  GPS  Compass  / 
ComNav Vector G1 GPS Satellite Compass for details of installation. 
 

1.7.1  Connection of    Hemisphere V102/V104s/V200s GPS Compass / ComNav 

Vector G1 GPS Satellite Compass 

 
Connect  CW-376-5M  by  soldering  with  the  cable  of  Hemisphere  V102  GPS  Compass  / 
ComNav Vector G1 GPS Satellite Compass. (Hereafter referred to as 

“V102 GPS Compass”) 

Please prepare two CW-376-5M when connecting with Radar as GPS compass. 
 
1)  The terminal of the cables of V102 GPS Compass is not processed, and 8 lead wires and 

1 shield wire are open. Brown and blue lead wires are connected to TX/RX of Port A, white 
and  green  lead  wires  are  connected  to  TX/RX  of  Port  C,  black  and  red  lead  wires  are 
connected  to  +/-  of  power  supply,  and  yellow  lead  wire  is  connected  with  earth.  Orange 
lead wire and shield wire are unconnected. 

Refer  to  the 

“Connection  table  of  V102  GPS  Compass”

,  and  solder  CW-376-5M  with 

Port  A  and  power  supply  of  cable  of  Hemisphere  V102  GPS  Compass.  Please  solder 
another CW-376-5M with Port C, when connecting with Radar as GPS compass. Please 
branch yellow wire (GND) of the cable of V102 GPS Compass into four, two of which shall 
be  soldered  with  each  black  (RX-)  and  red  (TX-)  of  CW-376-5M.  After  soldering  is 
completed, be sure to process the connected part by self-adhesive tape etc. to be water 
resistant and insulated. 

 
 
 
   
 
 
 
 
 
 
 
     
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Fig. 1.57 Connection of V102 GPS Compass

 

CW-376-5M 

 

Cable of V102 GPS Compass 

Blue and shield 

White 

 

Orange 

 

Green 

 

Red 

 

Black 

 

 
 

Red 

Black 

White 

 
Orange

 

Black 

Brown 

Blue 

 

Red 

 

Yellow 

 

Yellow 

 

 
 

Yellow 

Yellow 

Green 

 
White 
 
Orange 

 
Shield

 

To NMEA terminal of Radar 

CW-376-5M 

Solder

e

d

 

To J3 connector of 

CVS-875D/877D

 

 

Port A/Power 

 

Port C 

Yellow wire is branched into 4. 

Unconnected 

Solder

e

d

 

Содержание CVS-875D



























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды