background image

Chapter 1 Installation 

 

CVS-875D/877D 

 

1-14 

 

0092607072-01 

2) In the case of steel boat (For Anti-resonance) 

With reference to the figures below, install the transducer at a shipyard.   

 

 

 

 

 

 

 

 

 

               

 

                                                     

   

 

 

 

 

 

 

 

                                                                 

 

 

 

 

 

 

 

 

 

 

 

 

 
Mounting components of a transducer on steel boat 

No. 

Name 

Material 

Qty 

Remarks 

Transducer unit (with bottom plate) 

 

 

Cable gland (CG-1) 

SS400 

Tank 

SS400 

By shipyard 

Mounting bolts 

SUS304 

Anticorrosive zinc (suggestion) 

Tank for TDM-052A/TDM-062A/ 
TDM-083. 
(Common to FRP, wood and steel boat) 
Material: SS400 t6.0 By shipyard 
 
 

Weld plate or rod to 
protect knocking the 
net or ropes 
 

 

Plumbing pipe 

This  pipe  should  be  extended 
up to draft line or junction box. 

 

Cable gland 

FRP, wood and steel boat protruding mounting kit. 
(For TDM-052A/TDM-062A/TDM-083) 
Material: SS400 t6.0 By shipyard 

You  can  remove  the  TD 
by removing this bolt. 

Wrap  and  fix 
with FRP. 

Unit: mm 

Содержание CVS-875D



























































































































Отзывы: