Koden CVS-875D Скачать руководство пользователя

Страница: 25 / 122

CVS-875D/877D

Chapter 1 Installation

0092607072-01

1-3

1.2 Installation of CVS-875D Display unit

CVS-875D Display unit can be installed either on desk-top or flush-mounted.

Install in the following procedure

1.2.1 Desk-top installation

(1) Decide the location to install the Display unit and keep the space for the maintenance

works as shown in Fig. 1.3.

(2) Mark the position where installation bracket are installed. (See Fig. 1.3)
(3) Confirm that the installation bracket matches the marked position. If not matched, correct

the marking position.

(4) Install the installation bracket in the installing location (screw hole) and fix it with 5

tapping screws (5mm) (M5 or pan-head). (Prepare 5 mm screws suitable for thickness of
installing location.)

(5) Place the Display unit on the installation bracket and fix the Display unit with washers

and knob bolts.

Display unit

M5 screw

(5 pcs)

Installation bracket

Knob bolt (2 pcs)

Fig. 1.2 Desk-top installation of Display unit

Unit: mm (inch)

Содержание CVS-875D



























































































































Результаты поиска

Содержание CVS-875D

Отзывы:

Похожие инструкции для CVS-875D

Бренды по названию

Популярные бренды

Koden CVS-875D, Руководство по установке

Результаты поиска

Содержание CVS-875D

Отзывы:

Похожие инструкции для CVS-875D

Бренды по названию

Популярные бренды