Koden CVS-875D страница 80 Скачать руководство пользователя

Страница: 80 / 122

Chapter 1 Installation

CVS-875D/877D

1-58

0092607072-01

Connection of USB Memory and SD Card [Owner supply]

The Operation unit is equipped with slots for USB memory and SD card.

There are card slots on the left side of the Operation unit. (See Fig.1.56) Connect the USB
memory or the SD card after removing the slot cover.

Put the cover firmly when the USB memory is not connected. Water may get inside if the slot
is not covered, and may cause failure.

SD card can be connected with the cover attached. Put the cover while SD card is connected
to avoid water intrusion..

Fig.1.56 Connection of USB Memory and SD Card

Caution : Connect/disconnect the USB memory and the SD card after turning

power supply OFF.

Caution : Please use the USB memory and the SD card KODEN recommends. If

the other device than recommended is used, KODEN does not assure
operation.

Caution : Water protection of the Operation unit is not guaranteed while the USB

memory is in use.

Caution : Water protection of the Operation unit is not guaranteed when the slot

cover is removed.

USB Memory

SD Card

Содержание CVS-875D



























































































































Результаты поиска

Содержание CVS-875D

Отзывы:

Похожие инструкции для CVS-875D

Бренды по названию

Популярные бренды

Koden CVS-875D, Руководство по установке

Результаты поиска

Содержание CVS-875D

Отзывы:

Похожие инструкции для CVS-875D

Бренды по названию

Популярные бренды