Knick Protos II 4400 Скачать руководство пользователя

Страница: 7 / 112

Operation in Explosive Atmospheres: PH 3400X-035 Module

The module is approved for operation in explosive atmospheres.

When installing the product in a hazardous location, observe the information in

the supplements to the certificates and, if applicable, the relevant control draw-

ings.

Observe all applicable local and national codes and standards for the instal-

lation of electrical equipment in explosive atmospheres. For orientation,

please refer to IEC 60079-14, EU directives 2014/34/EU and 1999/92/EC (ATEX),

NFPA 70 (NEC), ANSI/ISA-RP12.06.01.

WARNING! Possible impairment of explosion protection.

• Modules which have already been used shall be subjected to a professional

routine test before they may be operated in another type of protection.

• Prior to commissioning, the operating company must verify the intrinsic

safety in accordance with the installation regulations of IEC 60079-14 for

the complete interconnection of all equipment involved, including the

connecting cables.

• The interconnection of Ex and non-Ex modules (mixed assembly) is not

permitted.

• In hazardous locations the device shall only be cleaned with a damp cloth to

prevent electrostatic charging.

Maintenance

The Protos modules cannot be repaired by the user. For inquiries regarding

module repair, please contact Knick Elektronische Messgeräte GmbH & Co. KG

at www.knick.de.

Safety Instructions

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды