Knick Protos II 4400 Скачать руководство пользователя

Страница: 54 / 112

Parameter Setting

TC process medium
Note: Function check (HOLD) mode active

Menu Display

TC process medium

(Parameter selection Pg 53)

TC process medium

You can choose from:

• Linear (entry of TC coefficient)

• Ultrapure water

• Table

When measuring media with a known

temperature behavior, the output pH

value can be corrected using a table.

TC can be entered in 5 °C steps for

temperatures between 0 and +95 °C.

Then, the output pH value is cor-

rected by the corresponding TC value

depending on the measuring temper-

ature. Intermediate values are linearly

interpolated. In the case of lower or

higher temperatures (< 0 °C or

> 95 °C), the last table value is used

for calculation.

If the delta function has been acti-

vated (see Pg 53) simultaneously

with temperature compensation, the

temperature is compensated first and

then the delta value is subtracted.

When the TC correction for process

medium is switched on, ”TC” appears

in the display in measuring mode.

Module PH 3400-035 (Administrator)

24.0 °C

Return

TC process medium

Sensor data

Cal preset values

7.00 pH

ORP/rH value

Delta function

Input filter

Block

TC process medium (Administrator)

24.0 °C

Abort

Off

Linear

7.00 pH

Table

Ultrapure water

TC process medium (Administrator)

24.0 °C

Abort

7.00 pH

Table

Info

TC at 00°C:

TC at 05°C:

TC at 10°C:

TC at 15°C:

TC at 20°C:

+00.00%

Outp I1 5.70 mA

Favorites menu

°C

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды