Knick Protos II 4400 Скачать руководство пользователя

Страница: 52 / 112

Parameter Setting

Cal preset values: Calimatic buffer, Cal timer, Cal tolerance band
Note: Function check (HOLD) mode active

Menu Display

Cal preset values

Calimatic buffer

For automatic calibration, you must

define the buffer set you want to use.

For calibration, you must then use buf-

fer solutions from this buffer set in any

order.

The selected buffer set with the

nominal values of the individual buffer

solutions is displayed in gray.

The “Calimatic buffer” menu shows all

buffer sets available.

Select buffer set with enter.

Calibration timer

Entry of the time interval until the

next due calibration.
Adaptive cal timer

Automatically reduces the time until

the next due calibration when the

electrode is exposed to high stress

(temperature, extreme pH values).

Module PH 3400-035 (Administrator)

20.1 °C

Return

TC process medium

Sensor data

Cal preset values

7.00 pH

ORP/rH value

Delta function

Input filter

Block

Cal preset values (Administrator)

20.1 °C

Abort

Calibration timer

Knick 2.00 4.01

Calimatic buffer

7.00 pH

Cal tolerance band

Drift check

Knick

DIN 19267

NIST standard

NIST technical

Merck/Riedel

Mettler-Toledo

Hamilton

Cal timer (Administrator)

20.1 °C

Adaptive cal timer

7.00 pH

Calibration timer

Return

168 h

Off

Cal tolerance band

If the measured value leaves the tol-

erance band specified here for zero

and slope, an adjustment is automati-

cally performed during calibration.

Cal tolerance band (Administrator)

20.1 °C

Tolerance band check

7.00 pH

Return

Calibration data taken over when

Off

tolerance band exceeded

Tolerance Zero
Tolerance Slope

+00.20 pH
002.0 mV/pH

ORP check

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды