Knick Protos II 4400 Скачать руководство пользователя

Страница: 30 / 112

Automatic buffer recognition (Calimatic)

Automatic calibration using Knick Calimatic is performed with one, two, or

three buffer solutions. Protos automatically detects the nominal buffer value

on the basis of the electrode potential and the measured temperature. Any

sequence of buffer solutions is possible, but they must belong to the buffer set

defined during parameter setting.

The Calimatic takes the temperature dependence of the buffer value into

account. All calibration data is converted using a reference temperature of

25 °C/77 °F.
During calibration the module is in function check (HOLD) mode.

Current outputs and relay contacts of the module behave as configured

(Module BASE).

NOTICE!

Only ever use fresh, undiluted buffer solutions which belong to the selected

buffer set!

Menu Display

Automatic buffer recognition

Remove and rinse the electrode

(

NOTICE!

Electrostatic hazard.

Do not rub.),

then immerse it in the first buffer

solution.

Start by pressing softkey or enter.

Calimatic

Return

Cal medium: Buffer solution

Knick 2.00 4.01 7.00 9.21

When changing sensors perform

First cal for statistics!

Enter cal temp

25.6 °C

7.00 pH

+025.6 °C

Proceed

Calimatic

Return

Dip sensor in 1st buffer,

then ‘Start’ calibration.

25.6 °C

7.00 pH

Start

Display of selected buffer set

Select: Sensor replacement
Enter: calibration temp

Proceed by pressing softkey or enter.

Select: Calimatic

Calibration / Adjustment

Calimatic automatic buffer recognition

Sensor replacement

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды