Knick Protos II 4400 Скачать руководство пользователя

Страница: 14 / 112

ISM

Diagnostics

Sensor wear monitor

22.3 °C

Return

Sensor operating time
Autoclaving cycles

7.02 pH

SIP cycles

CIP cycles

Sensor wear

635 d

1 of 2

0 of 3

1 of 5

Sensor wear monitor (ISM only)

The Diagnostics menu provides single-glance

information on the current sensor wear.

In addition, the sensor operating time as well as

the number of executed autoclaving, CIP, or SIP

cycles are indicated.

Sensor diagram

Return

22.3 °C

7.02 pH

2 - Zero point

1 - Slope

4 - Glass impedance

3 - Ref impedance

5 - Response time

7 - Sensor wear

6 - Cal timer

Sensor diagram

• Slope

• Zero

• Reference impedance

• Glass impedance

• Response time

• Calibration timer

• Sensor wear

The measured values are continuously moni-

tored during the measurement process. The

sensor diagram provides at-a-glance informa-

tion about critical parameters. If a tolerance limit

has been exceeded, the respective parameter is

flashing.

Values in gray: Monitoring switched off.

Critical range –
“inner circle”
Value out of tolerance
The tolerance can be
modified as required!

“Outer circle”
Value within tolerance

Statistics

Indication of sensor data for the First Calibration

(adjustment) and the last 3 calibrations com-

pared to the First Calibration (date and time of

First Calibration, zero and slope, impedance of

glass and reference electrode, response time).
For ISM, the data are stored in the sensor.

Statistics

Return

Zero

22.3 °C

7.02 pH

Diff

+00.03 pH 02.05.07 13:24

1st Cal

+07.00 pH 13.04.07 10:03

Diff

+00.02 pH 15.05.07 09:18

Diff

+00.03 pH 02.06.07 10:47

Slope

he displa

y ma

y v

y depending on the devic

e v

ersion.

Содержание Protos II 4400

















































































































Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды

Knick Protos II 4400, Руководство пользователя

Результаты поиска

Содержание Protos II 4400

Отзывы:

Похожие инструкции для Protos II 4400

Бренды по названию

Популярные бренды