Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 38 / 44

background image

38

Accessories / Spare Parts

Adapter for additional medium

This adapter allows the introduction of an additional rinse medium

beyond the available media connection (media hose).

It is mounted between the Ceramat and the media hose multiplug.

The following variants are available:

• ZU 0654/1 Adapter PEEK, O-rings FKM

• ZU 0654/2 Adapter PEEK, O-rings EPDM

• ZU 0654/3 Adapter PEEK, O-rings FFKM

• ZU 0655/1 Adapter 1.4571, O-rings FKM

• ZU 0655/2 Adapter 1.4571, O-rings EPDM

• ZU 0655/3 Adapter 1.4571, O-rings FFKM

ZU 0631 standard-media interface

Sensor lock-gate connection kit for manual operation

(see ZU 0646) or for operation with a PLC.

ZU 0646 pneumatic manual control valve

Switch for manual operation (rocker switch to

reverse compressed air) on ZU 0631 standard-media

interface.

«
...
36
37
38
39
40
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: DARAY Страницы: 24

Бренд: Jafar Страницы: 9

Бренд: Malmet Страницы: 14

Бренд: Zempire Страницы: 2

Бренд: Datex-Ohmeda Страницы: 80

Бренд: MacDon Страницы: 2

Бренд: V-TAC Страницы: 6

Бренд: Taylor Страницы: 41

Бренд: Qlight Страницы: 3

Бренд: qtran Страницы: 2

Бренд: Q-Optics Страницы: 2

Бренд: Orliman Страницы: 11

Бренд: JTECH Medical Страницы: 8

Бренд: Synthetic Sound Labs Страницы: 12

Бренд: Skytrofa Страницы: 35

Бренд: Hammer Страницы: 21

Бренд: GYM form Страницы: 40

Life/form LF03608

Бренд: Nasco Healthcare Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды