Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 15 / 44

background image

15

Connecting the outlet hose

Turn the outflow nipple so that the outlet hose

points outwards (see figure on the left). Before

tightening the coupling nut, correctly align and

insert the outflow nipple!

Outlet hose

Coupling nut

Coding recesses

Coding bars

Outflow nipple

Information on Installation

Installing the sensor cable

(pH, oxygen, and conductivity cables)

Attach the connecting cable (A) to the sensor and

connect to the fixing bracket (B) in a loop as shown in

the illustration.

Using clamp (C), attach the cable lightly so that the

cable is secured and not constricted. The rotational

movement of the Ceramat would otherwise damage

the cable.

A

B

C

F

NOTICE

Check positioning of coding recesses and coding

bars to lock the connection.

NOTICE

The cable loop must be long enough so that the

cable does not impede the stroke movement of

the fitting.

Connect equipotential bonding cable to terminal

(F) (if required).

«
...
13
14
15
16
17
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: ABB Страницы: 36

Бренд: ABB Страницы: 40

Бренд: Zetec Страницы: 23

Бренд: Garmin Страницы: 10

Бренд: Naviom Страницы: 31

Бренд: Uchida Yoko Страницы: 40

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

Бренд: Ganter Norm Страницы: 20

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Бренд: ebm-papst Страницы: 10

CEAG Exit Cube 33822 LED CGLine+

Бренд: Eaton Страницы: 20

Бренд: swamp Страницы: 5

Бренд: Lites Страницы: 8

Бренд: Taylor Страницы: 82

Бренд: Tascam Страницы: 100

Monolith NT.115

Бренд: Nano Temper Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды