Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 13 / 44

background image

13

Information on Installation

For operation of the Ceramat, you must connect control air, rinsing or calibration media, and the

electrical check-back signal for indicating the probe position.

There are two basic options for this.

When the Ceramat is operated with a Unical or Uniclean electro-pneumatic controller and the Protos measur-

ing system, the cables and tubings for air pressure, rinsing/calibration media and check-back are combined in

a single hose with just one plug connection (multiplug). This hose is referred to as media connection.

This media connection is installed on the Ceramat together with the outlet hose.

When you do not use a probe controller (Unical or Uniclean and Protos measuring system), you can connect

the supply lines for control air, rinsing/calibration media and electrical check-back to the Ceramat with a free

hose connection via the ZU 0631 standard-media interface.

Connection for operation with

Unical/Uniclean und Protos

Connection for operation with

ZU 0631 standard media interface

«
...
11
12
13
14
15
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: Bartscher Страницы: 22

Sportsound SSR-300

Бренд: Daktronics Страницы: 42

Бренд: Federal Signal Corporation Страницы: 2

Бренд: Harman Kardon Страницы: 7

Бренд: Xiitech Страницы: 6

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Life/form SmartScope LF01142U

Бренд: Nasco Страницы: 2

Бренд: Guyatone Страницы: 2

Бренд: Milestone Страницы: 64

Бренд: Bowa Страницы: 140

Бренд: Toparc Страницы: 32

Бренд: U.S.SAWS Страницы: 21

ClusterStor H-6167

Бренд: Cray Страницы: 39

Elitco Lighting C202

Бренд: ELEGANT Страницы: 2

NESLAB System IV

Бренд: Thermo Scientific Страницы: 22

Бренд: QTX Light Страницы: 4

BinTrac HouseLINK HL-10P

Бренд: herdstar Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды