Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 36 / 44

background image

36

Accessories / Spare Parts

Long sensor socket with mounted O-rings

This sensor socket is recommended for brittle

incrustations (eg, lime).

(Hastelloy C22 material can be identified by a

missing grip recess.)

• ZU 0672/A Sensor socket 1.4571, O-rings FKM

• ZU 0672/B Sensor socket 1.4571, O-rings EPDM

• ZU 0672/C Sensor socket 1.4571, O-rings FFKM

• ZU 0673/A Sensor socket Hastelloy, O-rings FKM

• ZU 0673/B Sensor socket Hastelloy, O-rings EPDM

• ZU 0673/C Sensor socket Hastelloy, O-rings FFKM

Grip recesses

Sensor socket, full sensor protection with

mounted O-rings

This sensor socket is recommended for brittle

incrustations (eg, lime). In addition, the sensor is

better mechanically protected.

(Hastelloy C22 material can be identified by a

missing grip recess.)

• ZU 0808/A Sensor socket 1.4571, O-rings FKM

• ZU 0808/B Sensor socket 1.4571, O-rings EPDM

• ZU 0808/C Sensor socket 1.4571, O-rings FFKM

• ZU 0820/A Sensor socket Hastelloy, O-rings FKM

• ZU 0820/B Sensor socket Hastelloy, O-rings EPDM

• ZU 0820/C Sensor socket Hastelloy, O-rings FFKM

Grip recesses

«
...
34
35
36
37
38
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: Labnet Страницы: 5

Бренд: Obdstar Страницы: 10

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: Kärcher Страницы: 148

Бренд: Park House Healthcare Страницы: 32

Бренд: Y.I.C. TECHNOLOGIES Страницы: 6

Бренд: LSI Страницы: 24

Бренд: Guyatone Страницы: 2

Бренд: Kaiweets Страницы: 6

Бренд: Kaiweets Страницы: 6

Pro hunter 2525

Бренд: SprotDog Страницы: 28

Бренд: Softing IT Networks Страницы: 54

Бренд: Velp Scientifica Страницы: 123

Бренд: IKA Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды