Knick Ceramat WA 153 Скачать руководство пользователя

Страница: 24 / 44

Maintenance Work on the Drive Unit

The drive unit must be removed, for example:

• for general maintenance or inspection

• to clean the calibration chamber, eg, after a sensor has broken

• to change the sensor / calibration-chamber gaskets

• in the event of a technical fault of the drive unit.

Position indicator

NOTICE

Before working on the drive unit make sure that the sensor lock-gate is in SERVICE position. This position is

attained by: the service switch (see Unical 9000(X) installation manual) or the “Maintenance” menu of the

Protos 3400(X) (see user manual of PHU 3400(X)-110 module).

While working on the sensor lock-gate, other persons must be prevented from actuating the control unit.

The position indicator shows whether the sensor lock-gate is in SERVICE position.

WARNING

When the drive unit must be removed under process conditions, be sure to wear protective clothing,

gloves, and goggles to protect yourself against process fluid that might escape. The drive unit serves as

second barrier after the ceramic rotary slides, i.e. even after a breakage in the ceramics or a defect in the

probe housing an uncontrolled escaping of process fluid is prevented. When removing the drive unit

under process conditions, you must check whether the first barrier (rotary slides, probe housing) functions

properly.

Содержание Ceramat WA 153













































Результаты поиска

Содержание Ceramat WA 153

Отзывы:

Похожие инструкции для Ceramat WA 153

Бренды по названию

Популярные бренды

Knick Ceramat WA 153, Руководство пользователя

Результаты поиска

Содержание Ceramat WA 153

Отзывы:

Похожие инструкции для Ceramat WA 153

Бренды по названию

Популярные бренды