Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 17 / 44

background image

17

Connection to Unical or Uniclean

The media connection is available in 5 m, 10 m, 14 m, or 17 m length (other lengths on request).

It consists of a Ø 30 mm corrugated hose with a metal coil.

You can also order special lengths (also heated or with wall ducts).

2 variants are available:

• for rinsing only (without branch outlet to media adapter)

• for calibration and cleaning function (with branch outlet to media adapter)

Connections

The connections for media adapter and sensor lock-gate are of a plug-in design. They are mechanically fixed

by screwing. Each fluid is fed to the sensor lock-gate through a separate tube of the media connection.

Check valves in the multiplug minimize contamination and prevent mixing of the calibration fluids.

Connection to Unical or Uniclean

The corrugated hose is screwed to the joining piece of the Unical or Uniclean.

You can easily feed the different media tubes through the slit in the securing nut. The different tube lengths

and diameters provide for a clear assignment to the different connection points (color coded).

See also Unical 9000(X) / Uniclean 900(X) installation manual.

Connection to media adapter

This connection is plugged and screwed to the media adapter. It includes the media tubing.

Electrical connection is made via a plug-in connector.

See also Unical 9000(X) / Uniclean 900(X) installation manual.

Connection to Unical 9000(X)

or Uniclean 900(X)

Connection to media adapter

(omitted for “rinsing only” variant)

Multiplug for connecting the Ceramat

«
...
15
16
17
18
19
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: B&K Страницы: 5

Бренд: B&K Страницы: 28

Бренд: JB-Lighting Страницы: 60

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

RIDA qLine ZG2601

Бренд: R-Biopharm Страницы: 23

Бренд: Igema Страницы: 22

Бренд: MAGSTIM Страницы: 86

Tacx Boost Bundle

Бренд: Garmin Страницы: 12

Бренд: AVID LABS Страницы: 20

Бренд: Briteq Страницы: 12

Бренд: Crary Страницы: 56

Бренд: Osram Страницы: 30

Spacelabs Medical 92506

Бренд: OSI Systems Страницы: 92

VL4000 BeamWash Luminaire

Бренд: Vari Lite Страницы: 190

Бренд: Marcy Страницы: 27

Бренд: Rocker Страницы: 23

Бренд: Western Global Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды