Knick Ceramat WA 153 Скачать руководство пользователя | Manualshive

Страница: 8 / 44

background image

8

Product Coding

WA 153-

Explosion protection

For hazardous area Zone 1
Without

Sensor

Sensor, Ø 12 mm with PG 13.5
pH sensor Ø12 mm with pressurization, pres-

sure chamber for compressed air supply
Optical sensor, Ø 1/2” (12.7 mm)
Optical sensor, Ø 12 mm

Material of gaskets

FKM
EPDM
EPDM - FDA
FKM - FDA
FFKM - FDA
FFKM

Material of

sensor protection sleeve

Hastelloy C22

PEEK
1.4404

Titanium

Material of sensor socket

Hastelloy C 22, without protection
Hastelloy C 22, short protection
1.4404, without protection
1.4404, short protection
1.4404, long protection
1.4404, full protection
PEEK, without protection
Titanium, without protection
Titanium, short protection

Scraper for sensor socket

Without
PEEK, natural

Immersion depth

Special immersion depth 23-104 mm (1 mm increments)
Immersion depth 105 mm (max.)

Process-wetted material

Hastelloy C22

1.4404

Titanium

Process adaptation

Flange, loose, 1.4571, PN10/16, DN 50
Flange, loose, 1.4571, PN10/16, DN 65
Flange, loose, 1.4571, PN10/16, DN 80
Flange, loose, 1.4571, PN10/16, DN 100

Flange, loose, 1.4571, PN10/16

,

DN 125

Flange, loose, 1.4571, PN10/16

,

DN 150

Flange, loose, 1.4571, PN10/16

,

DN 200

Flange, loose, 1.4571, PN40, DN 50
Flange, loose, 1.4571, PN40, DN 65
Flange, loose, 1.4571, PN40, DN 80
Flange, loose, 1.4571, PN40, DN 100

Flange, loose, 1.4571, PN40, DN 125

«
...
6
7
8
9
10
...
»

Содержание Ceramat WA 153













































Отзывы:

Нет отзывов

Похожие инструкции для Ceramat WA 153

Бренд: Falcon Страницы: 12

Бренд: Barreto Страницы: 20

Бренд: Barreto Страницы: 18

Бренд: Backyard Discovery Страницы: 41

Бренд: Vahterus Страницы: 31

Бренд: HEINE Страницы: 4

Бренд: Harken Industrial Страницы: 6

Бренд: Nahita Страницы: 31

electronic music instrument

Бренд: Quintet Страницы: 35

Aesculap 012978

Бренд: B. Braun Страницы: 30

DualBurn CDR-882

Бренд: HHB Страницы: 2

Бренд: XFT Medical Страницы: 44

PACSystems RXi ICRXIBN7E001A

Бренд: GE Страницы: 8

Бренд: Exo Terra Страницы: 11

Бренд: Olympus Страницы: 74

Mini MR standard

Бренд: IKA Страницы: 40

Бренд: IKA Страницы: 104

Бренд: Game Winner Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды