manualshive.com logo in svg

Klimaire Ecosaire CM Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Klimaire Ecosaire CM Series Скачать руководство пользователя страница 89

Owners Manual              Ecos

aire

®

CM Series Precision Air Conditioner

Ecos

aire

®

July 2007                                                                                                                                                                                               89

Data subject to change without notice.

HOW TO INSTALL THE REPLACEMENT CYLINDER

1. Reverse procedure should be followed to install the new cylinder.  

The branch-circuit disconnect is to be left 

open until the cylinder is completely installed and reconnected.

2. Ensure that the cylinder is secured properly by the re-usuable tie wrap and mounting brackets within the unit.
3. The cylinder plug wires are color-coded in accordance with the colored dots beside the electrode pins on top of 

the cylinder. This color-coding 

MUST

be adhered to when replacing cylinder plugs on pins.

4. With cylinders having 

six primary voltage cylinder plugs

, it should be noted that there are

two of each color

.  

5. Care 

MUST

be taken so that the cylinder 

leads of the same color

are always 

directly opposite each other

as indicated by the dot formation on the top of the cylinder.

6. The white cylinder plug on all units is for the sensor electrode which 

always

goes on the single pin surrounded 

by a plastic shoulder.

7. Ensure that cylinder plugs fit snugly on the pins.
8. If cylinder plugs become loose, it is best to obtain a new replacement plug.

EXTENDED SHUTDOWN

Before disconnecting power to the humidifier for a period of extended shutdown, 

ALWAYS DRAIN

the cylinder

first.  Otherwise, the electrodes are subject to harmful corrosion which drastically shortens cylinder life.  

DO NOT

leave the switch in the 

DRAIN

position indefinitely as the drain coil could burn out.  Leave the switch in the 

OFF

position and “open” the main external fused disconnect to stop power to the humidifier.  Close the shut off valve in
the water supply line feeding the humidifier.

Humidifier                                Maintenance                             Operation 

OPERA

TION

Содержание Ecosaire CM Series












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды