manualshive.com logo in svg

Klimaire Ecosaire CM Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Klimaire Ecosaire CM Series Скачать руководство пользователя страница 30

Air-Cooled Direct-Expansion and Air-Cooled DualCool Units Only

Ecos

aire

®

CM Series Precision Air Conditioner              Owners Manual

30

Ecos

aire

®

July   2007

Data subject to change without notice.

Installation                               Piping              Refrigerant-Tube Joining   

After eliminating all leaks, locate the refrigerant receiver in the remote condenser

unit.  Open the rotalock valves on the receiver.

evacuation manifold
(by others)

essential electronic
evacuation gauge
(by others)

hose (by others) to
hot-gas-tube access
valve

liquid-line access valve
added previously 
(by others)

Open the compressor service valves (if any) to the access (middle) position.  The

Ecosaire® unit, condenser, and tubes must be evacuated to a pressure below 500
microns of mercury as measured by an electronic vacuum gauge.

Compound gauges

as found on refrigeration manifolds are inadequate.
IMPORTANT!

Under no circumstances use the compressor as a vacuum pump or apply power to a compressor under

vacuum.  Damage to the motor windings will result.

Connect a good set of refrigeration service gauges, an electronic micron-level vacuum gauge, and a vacuum pump

as shown below.  Use core-removal adapters to remove the cores from Schraeder-type access valves.

To insure a correct vacuum reading, install the electronic vacuum gauge far away from the vacuum pump

or use a reliable vacuum valve to isolate the gauge and system from the pump while reading the vacuum. 

Colder ambient temperatures require longer evacuation times.  Allow enough time at low pressures to remove any

water from the tubes.  The triple-evacuation method can be helpful.

After proper evacuation, break the vacuum with vapor refrigerant until a positive pressure is reached.

Replace the access valve cores and remove the adapters.
Close the compressor rotalock valves. 

Add the specified weight and type of refrigerant (by others), as calculated on previous page, through the high-

pressure access valve.  

DO NOT put liquid refrigerant into the low-pressure access valve.

Open compressor
rotalock valves to
access position during
evacuation.

INST

ALLA

TION

SAMPLE

Number and location of

component

s may vary

.

SAMPLE

Number

, location, and

appearnce of component

s

may vary

.

Содержание Ecosaire CM Series












































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды