Klimaire Ecosaire CM Series Скачать руководство пользователя страница 55

Страница: 55 / 107

Owners Manual Ecos

aire

CM Series Precision Air Conditioner

Ecos

aire

July 2007 55

Data subject to change without notice.

For glycol coolers, be sure that the system is full of glycol solution.
Turn off electrical power to the remote heat exchanger.

Carefully attach a temporary jumper to the enable input of the remote

heat exchanger, as shown.

Close the electrical enclosure of the remote heat exchanger.
Turn on the electrical power to the remote heat exchanger.

Confirm that the fans (and pumps, if any) of the remote heat exchanger

operate.

For remote heat exchangers with three-phase fans, confirm that the

fans turn in the proper direction to blow air upward. If they do not, a
qualified person should disconnect power from the remote heat
exchanger, swap any two branch-circuit wires, and re-connect electrical
power to the remote heat exchanger.

Do not move any factory-

installed wires.

For Air-Cooled Direct Expansion and Air-Cooled DualCool units,

remove the temporary jumper installed in step above. For all others,
leave jumper in place and go to next page.

Adjust Remote Heat Exchanger Controls

Startup

Air-Cooled Direct Expansion, Glycol-Cooled Direct Expansion,

Air-Cooled DualCool, & Glycol-Cooled DualCool Units Only

SAMPLE

Number and location of

component

s may vary

ARTUP

Содержание Ecosaire CM Series












































































































Результаты поиска

Содержание Ecosaire CM Series

Отзывы:

Бренды по названию

Популярные бренды

Klimaire Ecosaire CM Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Ecosaire CM Series

Отзывы:

Бренды по названию

Популярные бренды