background image

8

VISION 1460 OWNER’S GUIDE

main features

GWA (Ground When Armed)

The 1460 feeds a (–) Ground output while the system is Armed.  

Optional devices can be activated by this control line, such as 

a Starter Kill Immobilizer Relay or LED scanners.  When the 

system is Disarmed, GWA is switched OFF and all attached devices turn 

off.  

See the 

Installation Guide

 for electrical specifications.

A “sector” is the Ignition, Hood, any Door, or attached Sensors. 

When a sector triggers the siren a certain number of times (see 

below), that sector is bypassed (disabled) until you Disarm and 

Arm again. This limits noise pollution caused by multiple siren 

triggers in a short period of time (such as when you park near 

construction sites or if animals jump on the vehicle repeatedly).

DOOR/TRUNK/HOOD

  —  If  left  OPEN,  the  siren  blasts  up  to 

5  times

 

(30s each time), then the Doors/Trunk/Hood are bypassed until closed. 

(The 

(+)12v Trigger

 WHT/BLK input is bypassed after triggering 

10 times).

IGNITION

 — If the Ignition is left ON, the siren blasts up to 

10 times

 (30s 

each time) and then the Ignition is bypassed until you Disarm & Arm again.

SENSOR

 — 

Warning triggers

 (5 chirps) and 

Full Triggers

 (30s siren) 

are independently bypassed after 

10 times

.  You must Disarm and then 

Arm again to re-activate.

SBS (Sector Bypass System)

HOOD TRIGGER

On compatible vehicles (or on any vehicle when the op-

tional  analog  Hood  input  is  connected),  the  siren  will 

blast  for  30  seconds  when  the  hood  is  opened  while 

Armed.  

See bottom half of page 4 on how to Disarm.

  

ERROR CHIRP

If a Door or the Hood or Trunk is open when you Lock/Arm, you will hear 

1 chirp (if Confirmation Chirps are enabled) followed by 

2 chirps

 (even if 

Confirmation Chirps are disabled). The 2 chirps are Error Chirps that no

-

tify you the doors/trunk/hood will be bypassed (they won’t trigger the siren) 

because they are open.  But 5s after you close the door/trunk/hood, they 

will then trigger the siren if later opened.  

You will only hear Error Chirps 

on cars that allow Lock/Unlock when the doors/trunk/hood are open.

OFF

Содержание 1460 series













































Отзывы: