Kipor Sinemaster IG2000i Скачать руководство пользователя страница 81

Страница: 81 / 90

Figure 28 Dismantle the spark plug

3. Dismantle the spark plug using a spark plug wrench.

4. Clean any dirt from around the spark plug base.

5. Visually inspect the spark plug. Discard it if the insulator is cracked or chipped.

Clean the spark plug with a wire brush if it is to be reused.

6. Measure the plug gap with a feeler gauge.

The gap shall be 0.7~0.8mm (0.028-0.031in). Correct as necessary by carefully

bending the side electrode.

Figure 29 Measure the clearance of spark plug

The spark plug must be securely tightened. An

improperly tightened plug can become very hot and

possibly damage the generator.

Never use a spark plug with an improper heat range.

7. Install the spark plug carefully, by hand, to avoid cross-threading.

8. After a new spark plug has been seated by hand, it should be tightened 1/2 turn

with a wrench to compress its washer.

If a used plug is being re-installed, it should only require 1/8 to 1/4 turn after being

seated.

9. Re-install the spark plug cap on the spark plug securely.

10. Re-install the spark plug maintenance cover.

Содержание Sinemaster IG2000i



























































































Результаты поиска

Содержание Sinemaster IG2000i

Отзывы:

Бренды по названию

Популярные бренды

Kipor Sinemaster IG2000i, Руководство по эксплуатации

Результаты поиска

Содержание Sinemaster IG2000i

Отзывы:

Бренды по названию

Популярные бренды