Kipor Sinemaster IG2000i Скачать руководство пользователя страница 20

Страница: 20 / 90

■

When an electric motor is started, both the overload indicator light (red) and the

output indicator light (green) may go on simultaneously. This is normal if the

overload indicator light (red) goes off after about four (4) seconds. If the overload

indicator light (red) stays on, consult your generator dealer.

Overload Reset Switch

Should the generator overload, AC power will be cut off but the engine will stay

running. Correct the overload condition and then press the overload reset switch on

the front panel. AC power will be restored immediately.

DC Operation

The DC receptacle may be used for charging 12 volt automotive style batteries only,

the no load voltage is 15V-30V.

■

In DC operation, turn the Smart-throttle switch to the OFF position.

Connect the charging cables to the DC receptacle of the generator and then to the

battery terminals.

Содержание Sinemaster IG2000i



























































































Результаты поиска

Содержание Sinemaster IG2000i

Отзывы:

Бренды по названию

Популярные бренды

Kipor Sinemaster IG2000i, Руководство по эксплуатации

Результаты поиска

Содержание Sinemaster IG2000i

Отзывы:

Бренды по названию

Популярные бренды