Keysight N2820A Скачать руководство пользователя страница 72

Страница: 72 / 110

N2820/1A User’s Guide

Probe Calibration

To Calibrate the Probe on InfiniiVision Oscilloscopes

ii) Turn on Averaging with

16 averages

iii) For both channels, set the V/div as small as possible to fit the

waveform on screen. For the zoomed-in channel, this should be

less than

. For the zoomed-out channel, this should be less

than

2mA

. If the waveform is not on screen at these settings,

increase the V/div and adjust the offset until these settings can

be used.
iv) Turn on

Vavg

measurements for both channels.

To set the zoomed-out offset, turn

using the supplied

screwdriver until the Vavg measurement is

+/- 1mA

To set the zoomed-in offset, turn

using the supplied

screwdriver until the Vavg measurement is

+/- 1mA

Figure 34

Location of Calibration Adjustments

Press the Channel on/off key to turn the channel on (if the

channel is off).

NOTE

The R2 and R4 adjustments are located on the underside of the probe

amplifier as displayed in

Figure 34

. The screwdriver provided with the

probe is the preferred adjustment tool.

Содержание N2820A















































































































Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды

Keysight N2820A, Руководство пользователя

Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды