Keysight N2820A Скачать руководство пользователя страница 54

Страница: 54 / 110

N2820/1A User’s Guide

Using N2825A Probe Heads

To Identify the R

SENSE

Resistance Using a Unique Name

To Identify the

SENSE

Resistance Using a Unique Name

This procedure allows you to identify the external DUT-mounted

SENSE

by a unique name. After completing the procedure, simply

connect the probe with the N2825A probe head, and select the

unique name on the oscilloscope. The proper

SENSE

value is used

for the measurements. Selecting a unique name is easier than

manually entering the

SENSE

resistance each time that you use the

N2825A head with a new

SENSE

Click the

Setup

Probe Configuration

menu command to view the

Probe Configuration dialog box.

Use the

Add Head

field to assign a unique name for each of your

N2825A/

SENSE

resistance associations.

Each time that you connect the probe, select the appropriate name

in the dialog box.

NOTE

This procedure is for Infiniium oscilloscopes, only. InfiniiVision

oscilloscopes do

not

support the assigning of names to identify

N2825A/R

SENSE

combinations.

Содержание N2820A















































































































Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды

Keysight N2820A, Руководство пользователя

Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды