Keysight N2820A Скачать руководство пользователя страница 16

Страница: 16 / 110

N2820/1A User’s Guide

General Information

Safety Information

WARNING

Observe Probe Ratings.
Do not apply any electrical potential to the probe input which exceeds

the maximum rating of the probe. Make sure to comply with the voltage

versus frequency derating curve found in this manual.

WARNING

Keep Away From Live Circuits.
Avoid open circuitry. Do not touch connections or components when

power is present.

WARNING

Indoor Use Only.
Do not operate in wet/damp environments. Keep product surfaces dry

and clean.

WARNING

Do Not Operate With Suspected Failures. Refer to qualified service

personnel.

WARNING

Never leave the probe connected to a conductor while it is not connected

to an oscilloscope or voltage measuring instrument.

WARNING

Do not use a probe which is cracked, damaged or has defective leads.

WARNING

Do not install substitute parts or perform any unauthorized modification

to the probe.

WARNING

Do not operate the probe or oscilloscope in the presence of flammable

gasses or fumes. Operation of any electrical instrument in such an

environment constitutes a definite safety hazard.

Содержание N2820A















































































































Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды

Keysight N2820A, Руководство пользователя

Результаты поиска

Содержание N2820A

Отзывы:

Бренды по названию

Популярные бренды