Keysight Infiniium 8000 Series Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 162

background image

151

Theory of Operation

This

Service Guide

supports troubleshooting the Keysight Technologies

oscilloscopes to assembly level. Theory of operation is included only as
supplemental information. It is not comprehensive enough for component- level
troubleshooting.

Block- Level Theory

The front panel provides:

• Dedicated knobs and push buttons for major oscilloscope functions.

• An 8.4- inch (diagonal) color flat panel display with touchscreen for waveform display,

measurement setup, instrument control, and graphical user interface.

• Front panel USB port.

• BNC connectors for channel input signals.

• AutoProbe interface for probe power and probe control.

• A connection for probe compensation.

The rear panel provides several connections:

• The line power input.

• An GPIB connector, for connection to an oscilloscope controller.

• An RS- 232 connection.

• A parallel printer connection.

• XGA monitor connection.

• Mouse and keyboard connections.

• LAN 10/100 connection.

• Auxiliary Input BNC (not on 2 channel oscilloscopes).

• Output BNC.

• TTL trigger output BNC.

• USB Interface.

The oscilloscope has several assemblies and four attenuators. Use the oscilloscope block
diagram on the previous page for the following discussion.

«
...
149
150
151
152
153
...
»

Содержание Infiniium 8000 Series



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Infiniium 8000 Series

Бренд: Makita Страницы: 60

Бренд: JB-Lighting Страницы: 60

Бренд: FEAS Страницы: 72

Sportsound SSR-200

Бренд: Daktronics Страницы: 5

Бренд: Federal Signal Corporation Страницы: 12

Бренд: SAMCHULLY Страницы: 48

Бренд: HAGS Страницы: 5

Бренд: HAGER WERKEN Страницы: 2

Бренд: Omlet Страницы: 60

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: Tascam Страницы: 3

Бренд: Yamaha Страницы: 126

DM 2000 Version 2

Бренд: Yamaha Страницы: 8

VLR100 LED Series

Бренд: WE-EF Страницы: 3

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды