manualshive.com logo in svg

Keysight Infiniium 8000 Series, Руководство по обслуживанию

Поделиться
Скачать
Keysight Infiniium 8000 Series Скачать руководство пользователя страница 119

                                          Chapter 6: Replacing Assemblies

To remove and replace the display board

119

To remove and replace the display board

Use this procedure to remove and replace the display board. When necessary, refer to 
other removal procedures. The graphics in this chapter are representative of the 
oscilloscope at the time of this printing. Your unit may look different.

1

Disconnect the power cable and remove the top cover.

2

Disconnect these cables from the display board:

• Backlight primary cable

• Flat- panel display driver cable

3

Remove the Torx T10 screw that secures the display board to the chassis.

Figure 6-25

Removing the display board

4

While pulling connector’s lever back to release the latch, grasp the board at the 
top  corners  and  pull  it  straight  up  until  it  is  free  of  the  card  cage.

5

To replace the board, reverse the above procedure.

Be sure to observe correct polarity on all cables when replacing the board.

Backlight primary cable

Flat-panel display 
driver cable

Display board

T10 Torx Screw

Connector lever

Snap latch

Содержание Infiniium 8000 Series



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды