manualshive.com logo in svg

Keysight Infiniium 8000 Series, Руководство по обслуживанию

Поделиться
Скачать
Keysight Infiniium 8000 Series Скачать руководство пользователя страница 113

                                          Chapter 6: Replacing Assemblies

To remove and replace the keyboard, touch screen, and flat-panel display assemblies

113

To remove and replace the keyboard, touch screen, and flat-
panel display assemblies

Use this procedure to disassemble and reassemble the front panel assembly, including 
the keyboard and flat- panel display. When necessary, refer to other removal procedures. 
The graphics in this chapter are representative of the oscilloscope at the time of this 
printing. Your unit may look different.

1

Disconnect the power cable and remove the top and bottom cover.

2

Remove the front panel assembly from the chassis (see page 108).

3

Remove the ten Torx T10 screws that secure the front panel cover plate to the 
front casting. 

Figure 6-18

Front panel cover plate screws

4

Carefully feed the front- panel keyboard ribbon cable through the cable access 
hole while separating the front panel cover plate from the front casting.

The display driver cable and touch screen USB cable remain attached to the cover plate.

Keep Long Screws Separate for Re-assembly
The four screws that fasten the keyboard to the front panel plate are longer than those around the perimeter 
of the plate. Keep them separate for re-assembly.

Flat-panel display driver multi-colored 
cable

T10 Screws (10)

Cal cable

Touch screen 
USB connector

Keyboard ribbon 
cable

Содержание Infiniium 8000 Series



































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды