Keysight Infiniium 8000 Series Скачать руководство пользователя страница 120

Страница: 120 / 162

Chapter 6: Replacing Assemblies
To remove and replace the hard disk drive

120

To remove and replace the hard disk drive

Use this procedure to remove and replace the hard disk drive. When necessary, refer
to other removal procedures. The graphics in this chapter are representative of the
oscilloscope at the time of this printing. Your unit may look different.

When replacing the hard disk drive, order the appropriate kit:

Instructions provided in the kit supercede the instructions in this chapter.

Disconnect the power cable and remove the top sleeve.

Remove the CD- ROM and hard drive cables from the cable clamps.

Figure 6-26

Removing cables from cable clamps

Remove the two Torx T20 screws holding the shock mount in place (See Figure
6- 27).

Tilt the disk drive assembly forward and lift up to remove.

C A U T I O N

DO NOT LET THE DISK DRIVE FALL!
Support the drive while removing the screws so that the drive does not fall.

Remove the four Torx T10 screws holding the disk drive onto the shock mount.

No internal hard disk drive is installed in oscilloscopes that have option 017
installed.

Oscilloscope Model Number

Hard Disk Drive Replacement Kit Part Number

5483xA/D, 5485xA and DSO80000A

54855-68704

DSO/MSO8000A, DSO80000B

D81004-68701

Cable
clamps

Содержание Infiniium 8000 Series


































































































































































Результаты поиска

Содержание Infiniium 8000 Series

Отзывы:

Похожие инструкции для Infiniium 8000 Series

Бренды по названию

Популярные бренды

Keysight Infiniium 8000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium 8000 Series

Отзывы:

Похожие инструкции для Infiniium 8000 Series

Бренды по названию

Популярные бренды