manualshive.com logo in svg

Keba KeDrive D3-DA BG3, Руководство по эксплуатации

Поделиться
Скачать
Keba KeDrive D3-DA BG3 Скачать руководство пользователя страница 46

U

V

W

U

V

W

U  V  W

U  V  W

U  V  W

U  V  W

U  V  W

U  V  W

X31A

X31A

X31B

X31A

Figure 4.17  Position of the motor connections

Connector set for BG3 and BG4 (optional)

Designation

Article no.

Material number

Application

D3-XT 230/A

1400.806.0

094801

I/O terminals BG1 - BG4

D3-XT 232/A

1431.600.0

120753

Motor terminals 1x45A

D3-XT 232/B

1431.602.0

Motor terminals 1x45A / HDSL

D3-XT 233/A

1431.604.0

120752

Motor terminals 80 A

D3-XT 23A/A

1441.600.0

115982

Motor terminals BG4

4.8.4 

Switching in the motor cable

CAUTION!

Damage to the device due to switching in the motor cable!

Carelessness can cause damage to the device

Switching in the motor cable must take place with the power switched off and the power stage 

disabled, as otherwise problems such as burned contactor contacts or power stage damage 

may occur.

To interrupt the supply of power to the servomotor, the safety function STO is available, 
see Chapter 7.1.

4.8.5 

Electronic overload protection for the motor

The motor protection function acquires the motor frequency, the motor current and other 
parameters. Depending on these parameters shown in the device help and the motor 
rated motor current, the electronic motor protection triggers the protection function if 
there is an overload. 

 

y

As I

2

T monitoring with programmable rated motor current, the permissible 

multiple of the rated motor current, the trigger time and the speed-dependency 
of the rated motor current. For explanations, see device help. 

 

y

The I

2

T integrator acts as a thermal memory for the system.  

The thermal memory is retained while the motor is at standstill if the device is 
switched on. 

 

y

The devices do not retain the thermal memory if switched off, i.e. the electronic 
motor overload protection is reset by switching off and on again the power 
supply. 

The electronic motor overload protection can be increased by using a motor temperature 
sensor. 

46

1  Electrical installation

Operation Manual KeDrive D3-DA BG3 and BG4 

1804.200B.1-01    Date: 03/2023

Electrical installation

Содержание KeDrive D3-DA BG3





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды