manualshive.com logo in svg

Keba KeDrive D3-DA BG3, Руководство по эксплуатации

Поделиться
Скачать
Keba KeDrive D3-DA BG3 Скачать руководство пользователя страница 43

U  V  W

U  V  W

V W

V W

U V W

U

U

U

U V W

W

W

W

W

W

W

W

W

W

W

W

U  V  W

U

U

U

U

W

W

V W

V W

U

U

U

U  

U

Motor 2

3 

~

U  V  W

U  V  W

Holding brake (+)

Holding brake (-)

Motor 1

3 

~

Holding brake (+)

Holding brake (-)

PE

1

2

Figure A:

Recommended 

connection 

of the motor 

holding brake 

up to

 max. 2 A 

motor brake 

current.

U  V  W

U  V  W

U V W

U

U V W

U

U V W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

W

U  V  W

U

U

U

U

W

U V W

U V W

U

U  

U

Motor 2

3 

~

U  V  W

U  V  W

Holding brake (+)

Holding brake (-)

Motor 1

3 

~

Holding brake (+)

Holding brake (-)

PE

1

2

Holding brake (+)

Holding brake (-)

24 V DC
ext. 

24 V DC

+

Holding brake (+)

Holding brake (-)

24 V DC

+

Figure B:

Recommended 

connection 

of the motor 

holding brake 

from

 max. 2 A 

motor brake 

current

The temperature sensor connection is shown in the version with "standard encoder interface".

Figure 4.13  Connection of two servomotors with motor holding brake, KeDrive D3-DA BG3

Motor

3 

~

U  V  W

Holding brake (+)

Holding brake (-)

-

+

Hiperface DSL+

Hiperface DSL-

H

PE

Motor 

1

Recommended connection 

of the motor holding brake 

up to

 max. 2 A brake 

current. 

The two-wire connection 

for the encoder is 

connected to connector 

HDSL on the "Hiperface 

DSL" model (see order 

code).

Note:

 

In preparation and only for 

KeDrive D3-DA BG3 up 

to 45 A!

Figure 4.14  Connection of one servomotor with Hiperface DSL

®

43

1  Electrical installation

Operation Manual KeDrive D3-DA BG3 and BG4 

1804.200B.1-01    Date: 03/2023

Electrical installation

Содержание KeDrive D3-DA BG3





















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды