KEB combivert B6 Скачать руководство пользователя

Страница: 29 / 44

GB - 29

Error and Status Display

Display COMBIVIS display

dec hex Meaning

rAcc

reverse acceleration

67 43 Acceleration with the adjusted ramps in counterclo-

ckwise direction of rotation (reverse).

rcon

reverse constant

69 45

Acceleration / deceleration phase is completed and it

is driven with constant speed / frequency in counter

clockwise direction of rotation (reverse).

rdEc

reverse deceleration

68 44 Stopping with the adjusted ramps in counterclockwise

direction of rotation (reverse).

SLL

stall

71 47 This message is displayed if during constant operation

the load is limited to the adjusted current limit.

SSF

speed search

74 4A Speed search function active, that means that the

inverter attempts to synchronize onto a running

down motor.

STOP quick stop

79 4F The message is output if as response to a warning

signal the quick-stop function becomes active.

E. EF

Error ! external fault

31 1F An external signal has released an error at a pro-

grammable input.

E. Pu

Error ! power unit

12 0C General power circuit fault (e. g. fan)

E.Acc

Error ! maximum

acceleration

24 18

Acceleration exceeds the limit defined by Pn.79.

E. br

Error ! brake

56 38 This error can occur in the case of switched on brake

control.

The absence of a motor phase was detected at

brake release.

The load reaches the hardware current limitation at

brake release.

The load is below the minimum load level at brake

release.

E.buS Error ! Watchdog

18 12 Adjusted monitoring time (Watchdog) of communica-

tion between operator and PC / operator and inverter

has been exceeded. Check wiring and bus master

(PC or SPS).

E.Cdd Error ! calc. drive data 60 3C

Error: During the automatic motor stator resistance

measurement.

E.dOH Error ! Motor tempe-

rature

Error: Overtemperature of motor PTC. Error can only

be reset at E.ndOH, if PTC is again low-resistance.

No motor overheat connected, but activated in the

parameter. Install bridge between T1/t2.

resistance at the terminals T1/T2 >1650 Ohm

line breakage to the temperature sensor

Check motor cooling

motor overloaded

further on next side

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды