KEB combivert B6 Скачать руководство пользователя страница 31

Страница: 31 / 44

GB - 31

Error and Status Display

Display COMBIVIS display

dec hex Meaning

E. OC Error ! overcurrent

Occurs, if the specified peak current is exceeded.

Short cicuit at the output

Ground fault

motor cable too long

Phase error

EMC

The load is too big at turned off constant current

limit.

DC brake at high ratings active

Deceleration ramp or stopping jerk is adjusted too

short.

Braking transistor defective or missing

Acceleration ramp or stopping jerk is adjusted too

short.

The load is too big at turned off acceleration stop.

E. OH Error ! heat sink tem-

perature

Error: Overtemperature of power module. Error can

only be reset at E.nOH.

Installation position and minimum distances wrong

ambient temperature too high

Fan clogged or defective

insufficient air flow at the heat sink (soiled)

E.OH2 Error ! motor protec-

tion

30 1E Electronic motor protective relay has tripped (see

motor protection function of the inverter).

E.OHI Error ! overheat

internal

Error: Overheating in the interior: If the interior tem

perature has dropped by at least 3 °C, E.nOHI is

displayed. Then the error can be reset.

E. OL

Error ! overload (Ixt)

16 10 An overload exceeded the permissible time (depen-

dent on short time current limit and overload characte-

ristic). Overload error can only be reset if OL-counter

reaches 0% again and E.nOL is displayed.

motor wrongly wired motor wrongly wired

inverter not correctly dimensioned

encoder damaged

poor control adjustment (overshooting)

Mechanical error (moved too hard, blockade) or

overload in the application

further on next side

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды