KEB combivert B6 Скачать руководство пользователя

Страница: 24 / 44

GB - 24

CP-Parameter

CP.25 Max. constant current

This function protects the frequency inverter against switch off through overcurrent during

constant output frequency. When exceeding the adjusted value, the output frequency is

reduced until the value drops below the adjusted value. CP. 03 displays "SSL" at active

function.

CP.26 Speed search / condition

When connecting the frequency inverter onto a decelerating motor, an error can be triggered

by the differing rotating field frequencies. With activated speed search the inverter searches

for the actual motor speed, adapts its output frequency and accelerates with the adjusted

ramp to the given set value. During speed search CP.03 displays "SSF". The parameter

determines on what conditions the function operates.

In case of several conditions the sum of the value must be entered. Example: CP.26 = 12

means after reset

and

after auto-reset UP.

Value Condition

Function off

at control release

at switch on

after reset

after auto-reset UP

CP.27 Motor protection / response

The motor protective function protects the connected motor against thermal destruction

caused by high currents. The function corresponds largely to mechanical motor protective

components, additionally the influence of the motor speed on the cooling of the motor is

taken into consideration. The load of the motor is calculated from the measured apparent

current (CP.04) and the adjusted rated motor current (CP.29).

For motors with separately driven fan or rated frequency of a self-ventilated motor following

tripping times

(VDE 0660, part 104) apply:

1.2 • Rated current

≤

2 hours

1.5 • Rated current

≤

2 minutes

2 • Rated current

≤

1 minute

8 • Rated current

≤

5 seconds

In case of failure CP.27 activates the motor protection function and adjusts the correspon-

ding response as follows:

CP.27 Response

Description

Error,

restart after reset

Error message E.xx

Immediate switch off of the modulation. Correct the

error for the restart and activate reset.

The prewarning changes into an error. The drive

remains in the error state until a reset signal is

recognized.

further on next side

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды