KEB combivert B6 Скачать руководство пользователя страница 33

Страница: 33 / 44

GB - 33

Error and Status Display

Display COMBIVIS display

dec hex Meaning

E. UP

Error ! underpotential

2 Occurs, if the DC-link voltage falls below the per-

missible value.

Voltage losses through wrong cabling.

inverter rating too small

A digital input was programmed as external error input

with error message E.UP has released.

Mains contactor or input fuse defective

Input voltage is too low or instable

The supply voltage through generator / transformer

breaks down at very short ramps.

E.UPh Error ! Phase failure

3 One phase of the input voltage is missing (ripple-

detection)

PUIn

Error ! Power unit

invalid

14 0E Software version for power circuit and control card

are different. Error cannot be reset. Only at F5-G

B-housing.

A.Acc

Warning ! maximum

acceleration

106 6A

Acceleration exceeds the limit defined by Pn.79. The

response to this warning can be definied by Pn.81.

A.buS Warning ! Watchdog

93 5D Adjusted monitoring time (Watchdog) of communica-

tion between operator and PC / operator and inverter

has been exceeded. Check wiring and bus master

(PC or SPS). The response to this warning can be

programmed.

A.dOH Warning ! drive

overheat

96 60 The motor temperature has exceeded an adjustable

warning level. The switch off time is started. The

response to this warning can be programmed. This

warning can be generated only with a special power

circuit.

A.EF

Warning ! external

fault

90 5A An external signal has released an error at a pro-

grammable input. The response to this warning can

be programmed.

A.ndOH All-clear ! drive

overheat

91 5B The motor temperature is again below the adjusted

warning level. The switch off time is stopped.

A.nOH All-clear ! overheat

pow.mod.

88 58 The heat sink temperature is again below the adjusted

warning level.

A.nOHI All-clear ! overheat

internal

92 5C The temperature in the interior of the inverter is again

below the warning threshold.

A.nOL All-clear ! overload

(Ixt)

98 62 The load counter decreases again under the adjusted

warning level. The warning “overload“ is reset.

A.OH

Warning ! overheat

pow.mod.

89 59

A level can be defined, when it is exceeded this

warning is output. The response to this warning can

be programmed.

A.OH2 Warning ! motor

protection

97 61

Warning: electronic motor protective relay has tripped.

The response to this warning can be programmed.

further on next side

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды