KEB combivert B6 Скачать руководство пользователя страница 11

Страница: 11 / 44

GB - 11

Installation position and

min. distances

Protective system (EN 60529)

IP20

Operation temperature

-10…40 °C (14…104 °F)

30 mm

100 mm

1 inch

4 inch

150 mm

6 inch

Storage temperature

-25…70 °C (-13…158 °F)

Max. heat sink temperature

90 °C (194 °F)

Climatic category (EN 60721-3-3)

3K3

Environment (IEC 664-1)

Pollution degree 2

Vibration/Jolt according to

German. Lloyd; EN50155

The flat-rear design (projected) requires cooling measures by the

machine builder. This can be in the best case no further measure at

all (e.g. at cyclic operation with down times) up to the dissipation of

the entire, indicated heat loss at rated operation.

The COMBIVERT must be protected against aggressive

gases, aerosols and conductive dust !

3.2

EMC conform Installation

• Always apply the shielding of motor

and control cables over a large contact

surface on both sides.

• Distance between control and power

cables at least 10…20 cm (4…8 inch).

• Lay motor and power cable separately.

• If it cannot be avoided, cross control

and power cables in a right angle.

• Install all cables as close as possible

to the mounting plate - ideal in a metal

cable duct.

• Mount COMBIVERT well conducting

with the mounting plate. Remove the

paint beforehand.

You can find further instructions regarding

the EMC- conform wiring in the Internet

at KEB.

Installation and Connection

3.1

Control cabinet installation

Installation and Connection

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды