KEB combivert B6 Скачать руководство пользователя страница 28

Страница: 28 / 44

GB - 28

Error and Status Display

At KEB COMBIVERT error messages are always represented with an "E." and the appropri-

ate error in the display. Error messages cause the immediate deactivation of the modulation.

Restart possible only after reset or autoreset.

Malfunction are represented with an „A.“ and the appropriate message. Reactions to

malfunctions can vary. In the following the display and their cause are described. Status is

displayed witout any additions.

Display COMBIVIS display

dec hex Meaning

bbL

base block

76 4C The power modules for motor-de-excitation are locked

after opening the control release or after an error.

boFF

open brake

86 56 This message is depending on the adjustment of

the brake control mode. It is displayed during open

(release) the brake.

bon

close brake

85 55 This message is depending on the adjustment of

the brake control mode. It is displayed during close

(engage) the brake.

Cdd

calculate drive data

82 52 Measurement of the motor stator resistance.

Cddr

calculate drive data

ready

127 7F Measurement of the motor stator resistance success-

ful completed.

dcb

DC brake

75 4B Motor is decelerated by a DC-voltage at the output.

dLS

low speed / DC brake

77 4D Modulation is switched off after DC-braking.

FAcc

forward acceleration

64 40 Acceleration with the adjusted ramps in clockwise

direction of rotation (forward).

Fcon

forward constant

66 42

Acceleration / deceleration phase is completed and it

is driven with constant speed / frequency in clockwise

direction of rotation (forward).

FdEc

forward deceleration

65 41 It is stopped with the adjusted ramp times in clockwise

direction of rotation (forward).

HCL

hardware current limit 80 50 The message is output if the output current reaches

the hardware current limit.

LAS

LA stop

72 48 This message is displayed if during acceleration the

load is limited to the adjusted load level.

LdS

Ld stop

73 49 This message is displayed if during deceleration the

load is limited to the adjusted load level or the DC-link

current to the adjusted voltage level.

low speed

70 46 No direction of rotation pre-set, modulation is off.

nO_PU power unit not ready

13 0D This message is displayed if during deceleration the

load is limited to the adjusted load level or the DC-link

current to the adjusted voltage level.

noP

no operation

0 Control release (terminal ST) is not switched.

PLS

low speed / power off

84 54 No modulation after Power-Off.

POFF power off function

78 4E Is displayed during power-off function. Depending on

the programming of the function the inverter restarts

automatically upon system recovery or after a reset.

further on next side

Содержание combivert B6













































Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды

KEB combivert B6, Руководство по установке

Результаты поиска

Содержание combivert B6

Отзывы:

Похожие инструкции для combivert B6

Бренды по названию

Популярные бренды