Kamstrup ULTRAFLOW 54 DN150-250 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 64

Kamstrup ULTRAFLOW 54 DN150-250 Скачать руководство пользователя страница 32

TECHNICAL DESCRIPTION

ULTRAFLOW

®

54 DN150-250

5512-876 GB/04-2012/Rev. F1

32

8.6

Function

In the meter’s working range from min. cut off to saturation flow there is linear connection between the flow rate
and the number of pulses being emitted. The below diagram shows an example of the connection between flow
and pulse frequency for ULTRAFLOW

®

q

p

150 m³/h.

If the flow is lower than min. cut off or negative, ULTRAFLOW

®

sends no pulses. At flows exceeding the flow

corresponding to pulse emission at max. pulse frequency of 128 Hz, the max. pulse frequency will be maintained.
(See

Diagram 9

).

Table 11

shows the flows of the different

flow sizes/pulse figures at max. pulse frequency of 128 Hz.

q

p

Pulse figure Flow @ 128 Hz

[m³/h]

[imp/l]

[m³/h]

150

1

461

250

0.6

768

400

0.4

1152

600

0.25

1843

1000

0.15

3072

Table 11

According to DS/EN 1434 the upper flow limit q

s

is the highest flow at which the flow sensor may operate for short

periods of time (

<

1h/day,

<

200 h/year), without exceeding max. permissible error. ULTRAFLOW

®

has no functional

limitations as to the duration of the period, during which the sensor operates above q

p

.

Please note, however, that high flow velocities may cause cavitation, especially at low static pressure.

0

20

40

60

80

100

120

140

-50

50

150

250

350

450

F

re

q

u

e

n

c

y

[

H

z

]

Flow [m³/h]

Flow-frequency (q

p

150 m³/h)

Min. Cutoff

Saturation flow (125 Hz)

Diagram 9

«
...
30
31
32
33
34
...
»

Содержание ULTRAFLOW 54 DN150-250

































































Отзывы:

Нет отзывов