Kamstrup ULTRAFLOW 54 DN150-250 Скачать руководство пользователя страница 22

Страница: 22 / 64

TECHNICAL DESCRIPTION

ULTRAFLOW

54 DN150-250

5512-876 GB/04-2012/Rev. F1

7.5

Connection to calculator

7.5.1

ULTRAFLOW

54 and MULTICAL

, galvanically coupled

If ULTRAFLOW

54 and MULTICAL

are connected via output module (Y=1), ULTRAFLOW

is galvanically coupled

with the MULTICAL

calculator and is powered by this via the three-wire signal cable (cable length up to 10 m).

Battery life time in e.g. MULTICAL

602 is approximately 10 years depending on data communication to the

calculator.

See

paragraph 8.8.1

for electrical data on output module (Y=1).

Note:

It is not permitted to mount a supply module or battery in ULTRAFLOW

54 with output module (Y=1).

ULTRAFLOW

→

MULTICAL

→

GND

(Blue)

→

+3,6 V

(Red)

→

(Yellow)

Table 10

7.5.2

ULTRAFLOW

54 and MULTICAL

, galvanically separated

If ULTRAFLOW

54 and MULTICAL

are connected via output module (Y=2 or 3) ULTRAFLOW

54 is galvanically

separated from MULTICAL

See

paragraph 8.8.2

for electrical data on output module (Y=2 and 3).

Note:

Flow info cannot be read.

Diagram 2. Three-wire connection, MULTICAL

602/801 via output module (Y=2). Cable length up to 25 metres.

Diagram 3. Three-wire connection, MULTICAL

602/801 via output module (Y=3). Cable length up to 25 metres.

Содержание ULTRAFLOW 54 DN150-250

































































Результаты поиска

Содержание ULTRAFLOW 54 DN150-250

Отзывы:

Kamstrup ULTRAFLOW 54 DN150-250, Техническое описание, Страница: 22 / 64

Результаты поиска

Содержание ULTRAFLOW 54 DN150-250

Отзывы: