Kaba Saflok SYSTEM 6000 Скачать руководство пользователя страница 8

Страница: 8 / 132

PND6000_ac_12_10

2010 SAFLOK

SAFLOK System 6000

™

Property Network Diagram

Minimum Equipment Requirements & Recommendations

ENCODER

WITH USB

CONNECTION

KEY CONTROL

CAT 5 CABLE

NETWORK

PRINTER

CAT 5

CABLE

RS232 CABLE

CLIENT

USB

CAT 5 CABLE

ENCODER

WITH TCP/IP CONNECTION

ENCODER

WITH

SERIAL

CONNECTION

SAFLOK

SERVER

ENCODER

WITH TCP/IP CONNECTION

SWITCH

(This diagram assumes that an Ethernet 10/100 multi-port hub is installed on the network.)

SAFLOK

™

Server

• Operating system: Windows XP Professional or Windows Server

2003 (Windows Server 2003 is required if over ten [10] workstations);

appropriate server and client licensing is required

• Minimum hardware specifications: Multi-core, 2 GHz or greater

CPU / 4GB or greater RAM / 100GB available hard drive space

• Virtual Machine environments are supported with the following

minimum resource allocation: Multi-core, 2 GHz or greater CPU

allocation / 4GB or greater RAM / 100GB available hard drive space

• If more than two (2) workstations are to be used with

Saflok, an Ethernet network hub or switch is required

• If connecting an encoder and/or handheld LPI device

directly to server, at least one (1) USB port must be

available for encoder connection and at least one (1)

dedicated Serial port for handheld LPI connection

• If including a Serial property management system

(PMS) interface, at least one (1) dedicated Serial

port must be available. TCP/IP interface support

is also available.

• Internet access is required to enable SAFLOK

remote real-time support via the web

• Anti-virus software is highly recommended
• UPS and surge protection with equipment

warranty are suggested

Client Workstation(s)

• Operating system: Windows XP, Vista, or Windows 7
• Minimum hardware specifications: 1 GHz processor,

1GB of RAM, and 10GB available hard drive space

• If connecting an encoder and/or handheld LPI device

directly to workstation, at least one (1) USB port must

be available for encoder connection and/or at least one

(1) Serial port for handheld LPI connection; encoders can

also utilize a TCP/IP (network) or Serial connection

• Anti-virus software is highly recommended
• UPS and surge protection with equipment

warranty are suggested

Notes:

• All network installations and maintenance are the responsibility

of the individual customer and not SAFLOK.

• Due to the wide performance variability of different manufacturers’

hardware, SAFLOK cannot guarantee software compatibility with

all computers. If you require a list of computers that SAFLOK has

tested and deemed software-compatible, please contact SAFLOK

customer service at 1.800.999.6213.

• The customer is responsible for completing all software updates

(e.g., Windows operating system & anti-virus protection).

• If using a Serial interface with a Virtual Machine, the Virtual

Machine host computer must have an available dedicated Serial

port that can be allocated to the Saflok Server Virtual Machine.

Содержание Saflok SYSTEM 6000





































































































































Результаты поиска

Содержание Saflok SYSTEM 6000

Отзывы:

Похожие инструкции для Saflok SYSTEM 6000

Бренды по названию

Популярные бренды

Kaba Saflok SYSTEM 6000, Справочное руководство

Результаты поиска

Содержание Saflok SYSTEM 6000

Отзывы:

Похожие инструкции для Saflok SYSTEM 6000

Бренды по названию

Популярные бренды