JVC RX-DV31SL страница 20 Скачать руководство пользователя

Страница: 20 / 66

1-20 (No.22023)

3.3.11 Removing the feed motor

(See Figs.15 to 17)

• Remove the DVD servo board.
• Remove the clamper base.
• Remove the DVD traverse mechanism assembly.

(1) From the top side of the DVD traverse mechanism assem-

bly, remove the feed motor wire that is soldered to the spin-
dle motor board. (See Fig.15.)

(2) Remove the two screws

attaching the feed holder as-

sembly and then take out the feed holder assembly. (See
Fig.15.)

(3) Remove the screw

attaching the thrust spring. (See

Fig.16.)

(4) Remove the feed gear and lead screw in the direction of the

arrow. (See Fig.16.)

(5) Remove the two screws

attaching the feed motor. (See

Fig.17.)

Fig.15

Fig.16

Fig.17

Feed motor

Remove the solders.

DVD traverse mechanism assembly

Feed motor
wire

Spindle motor board

Feed holder
assembly

Feed holder assembly

Feed motor

Feed gear

Lead screw

Thrust spring

Feed holder assembly

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды