JVC RX-DV31SL страница 15 Скачать руководство пользователя

Страница: 15 / 66

(No.22023)1-15

3.3

DVD mechanism section

• Remove the top cover.
• Remove the front panel assembly.
• Remove the DVD mechanism assembly.

3.3.1 Removing the tray

(See Figs.1 and 2)

(1) From the left side of the DVD mechanism assembly, push

the slide cam in the direction of the arrow 1 and then pull
out the tray in the direction of the arrow 2. (See Fig.1.)

(2) Push the tray stoppers

in the direction of the arrow 3, pull

out the tray in the direction of the arrow 4. (See Fig.2.)

3.3.2 Attaching the tray

(See Fig.2)

When attaching the tray, insert the tray to the rail of the DVD
mechanism assembly and then push the tray in the DVD mech-
anism assembly.

Fig.1

Fig.2

3.3.3 Removing the tray

(See Fig.3)

(1) From the bottom side of the DVD mechanism assembly,

disconnect the card wires from the connectors CN201 and
CN202 on the DVD servo board.

Caution:

Be sure to solder the short land sections

on the flexible

wire before disconnecting the flexible wire from connec-
tor CN101 on the DVD servo board.
If the flexible wire is disconnected without attaching sol-
der, the DVD pickup unit may be destroyed by static
electricity.

(2) Release the locks of the connector CN101 on the DVD ser-

vo board in the direction of the arrow 1, disconnect the flex-
ible wire.

Caution:

In the assembly, be sure to remove solders from the
short land sections

after connecting the flexible wire to

the connector CN101 on the DVD servo board.

(3) While pushing the claws

of the DVD mechanism assem-

bly in the direction of the arrow 2, remove the DVD servo
board in an upward direction.

Fig.3

Tray

Slide cam

DVD mechanism assembly

Tray

Tray stoppers

DVD mechanism assembly

Claw

CN201

CN202

CN101

DVD servo board

Short land sections

Card wire

Flexible wire

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды