JVC RX-DV31SL Скачать руководство пользователя страница 14

Страница: 14 / 66

1-14 (No.22023)

3.2.2

Removing the control board
(See Fig.23)

• Prior to performing the following procedures, remove the top

cover, front panel assembly and FL board.

Reference:

It is not necessary to remove the parallel wires from the FL
board.
(1) Remove the three screws

attaching the control board.

(2) Remove the solders from the soldered points

attaching

the parallel wire while lifting the control board.

Reference:

Remove the parallel wire as required.

3.2.3

Removing the indicator board
(See Fig.23)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the back side of the front panel assembly, remove the

two screws

attaching the lens holder.

(2) Remove the solders from the soldered points

on the FL

board attaching the parallel wire.

(3) Remove the solders from the soldered points

on the pow-

er switch board attaching the parallel wire.

Reference:

Remove the parallel wires as required.

Fig.23

3.2.4

Removing the power switch board
(See Fig.24)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the back side of the front panel assembly, remove the

two screws

attaching the power switch board.

(2) Remove the solders from the soldered points

on the pow-

er switch board attaching the parallel wire.

Reference:

Remove the parallel wire as required.

3.2.5

Removing the speaker SW. board
(See Fig.24)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the back side of the front panel assembly, remove the

three screws

attaching the speaker SW. board.

(2) Disconnect the wire from the connector CN703 on the FL

board.

Fig.24

Control board

Indicator board

Soldered point

Lens holder

FL board

Soldered point

CN703

FL board

Speaker SW. board

Power switch
board

Soldered
point

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды