JVC RX-DV31SL Скачать руководство пользователя страница 16

Страница: 16 / 66

1-16 (No.22023)

3.3.4

Removing the clamper base
(See Fig.4)

(1) From the top side of the DVD mechanism assembly, re-

move the four screws

attaching the clamper base.

(2) Remove the clamper base from the bosses d of the loading

base in an upward direction, remove the clamper base
from the sections

while sliding it in the direction of the ar-

row.

Fig.4

3.3.5

Removing the tray drive board
(See Fig.5)

• Remove the clamper base.

(1) From the bottom side of the DVD mechanism assembly,

disconnect the card wire from the connector on the tray
drive board.

(2) Remove the solders from the soldered sections

on the

tray drive board.

(3) Remove the screw

attaching the tray drive board to the

DVD mechanism assembly.

Fig.5

Clamper base

Boss

Section

Loading base

Motor

Tray drive board

DVD mechanism assembly

Soldered
sections

Connector

Card wire

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды