JVC RX-DV31SL страница 13 Скачать руководство пользователя

Страница: 13 / 66

(No.22023)1-13

3.2

Front panel assembly section

3.2.1 Removing the FL board

(See Figs.21 and 22)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the front side of the front panel assembly, pull out the

volume knob assembly in the direction of the arrow. (See
Fig.21.)

(2) From the back side of the front panel assembly, remove the

eight screws

attaching the FL board. (See Fig.22.)

(3) Disconnect the wire from the connector CN703 on the FL

board while lifting the FL board slightly. (See Fig.22.)

(4) Remove the solders from the soldered points

and

at-

taching the parallel wires while lifting the FL board. (See
Fig.22.)

(5) Take out the FL board from the front panel assembly.

Reference:

Remove the parallel wires as required.

Fig.21

Fig.22

Front panel
assembly

Volume knob assembly

CN703

Front panel

FL board

Wire

Soldered point

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды