JVC RX-DV31SL страница 11 Скачать руководство пользователя

Страница: 11 / 66

(No.22023)1-11

3.1.14 Removing the sub trans. Board

(See Fig.17)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the top side of the main body, remove the tie band

bundling the wires.

(2) Disconnect the card wire from the connector CN115 on the

sub trans. board.

(3) Disconnect the wire from the connector CN111 on the sub

trans. board.

(4) Disconnect the wire from the connector CN201 on the amp.

board.

(5) Remove the three screws

attaching the sub trans. board.

(6) From the reverse side of the sub trans. board, remove the

solders from the soldered points

attaching the wires.

3.1.15 Removing the fan motor

(See Figs.17 and 18)

• Prior to performing the following procedures, remove the top

cover and front panel assembly.

(1) From the top side of the main body, remove the tie band

bundling the wires. (See Fig.17.)

(2) Disconnect the fan motor wire from the connector CN122

on the main board. (See Fig.17.)

(3) From the front side of the main body, remove the four

screws

attaching the fan motor to the fan bracket. (See

Fig.18.)

(4) Take out the fan motor in the direction of the arrow. (See

Fig.18.)

Reference:

• When attaching the screws

, attach the wire holder and

wire clamp together with them. (See Fig.18.)

• After attaching the fan motor, bundle the wires using the wire

clamp. (See Fig.18.)

Fig.17

Fig.18

CN201

CN122

CN115

Amp. board

Fan motor

Fan motor
wier

Chassis base

Main board

Tie band

Fan
bracket

Soldered
points

Sub trans.
board

Fan motor

Wire clamp

Wire holder

Chassis base

Fan bracket

Содержание RX-DV31SL



































































Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды

JVC RX-DV31SL, Руководство по обслуживанию

Результаты поиска

Содержание RX-DV31SL

Отзывы:

Похожие инструкции для RX-DV31SL

Бренды по названию

Популярные бренды