JUKI APW-896/IP-420 Скачать руководство пользователя страница 88

Страница: 88 / 140

− 84 −

15. USING THE INFORMATION

There are three functions below, in the information function.

Maintenance inspection information

Oil replacement (grease-up) time, needle replacement time,
cleaning time, etc. are specified, and when the specified
time has passed, the warning notice can be performed.

See

“

-15-(1) Observing the maintenance inspection

information” p.85

Production control information

By means of function to display target production and
actual production, the target achieving consciousness of a

lne or a group s enhanced and also the progress can be

confirmed in one glance.

See

“

-15-(3) Observing the production control

information” p.87

and

“

-15-(4) Performing setting of

the production control information

” p.89

Operation measurement information

Information on machine operating situation, machine

operatng rate, ptch tme, machne tme, and machne
speed can be dsplayed.

See

“

-15-(5) Observing the operation measurement

information” p.91

Display the information screen

Press INFORMATION key

of the switch seat section

in the input screen and the information screen (screen A) is

dsplayed.

Information screen

(screen A)

Содержание APW-896/IP-420













































































































































Результаты поиска

Содержание APW-896/IP-420

Отзывы:

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 88 / 140

Результаты поиска

Содержание APW-896/IP-420

Отзывы: