manualshive.com logo in svg

JUKI APW-896/IP-420, Инструкция по эксплуатации, Страница: 10 / 140

Поделиться
Скачать
JUKI APW-896/IP-420 Скачать руководство пользователя страница 10

− 6 −

5. CONNECTING THE POWER PLUG 

Connection of the power plug to the power depends on the specifications of the product. Adjust the 

power plug to the power specifications to connect.

1

   In case of the product of single-phase, 200 to 240V specifications :

 

Connect the sky-blue and brown wires of the power cord to the power terminal (AC200 to 240V) 

and the yellow/green wre to the ground (earth) termnal respectvely.

2 

  In case of the product of 3-phase, 200 to 240V specifications :

 

Connect the red, white and black wires of the power cord to the power terminal (AC200 to 240V) 

and the yellow/green wre to the ground (earth) termnal respectvely.

3

   In case of the product with the optional high voltage transformer (with SA-128) :

 

Connect the black wires (3 pieces) of the power cord to the power terminal (AC380 to 415V) and 

the yellow/green wre to the ground (earth) termnal respectvely.

 

It is possible to connect to 380/400/415V by setting of the input tap of transformer (standard setting 

at the time of delivery : 380V). 

CAUTION 

: 

To prevent possible accidents caused by leakage or dielectric strength, an appropriate power plug 

shall be installed by a person who has an expert knowledge of electricity. Be sure to connect the 

power plug to the receptacle that is well grounded.

This product performs operation by the single-phase connection for 3-phasse 380/400/415V.

[Caution when changing the power source of the high voltage optional transformer]

When using high voltage optional transformer 

1

 with the input voltage of 400V or 415V, it is 

necessary to replace nput power source cord 

2

 

of high voltage optional transformer 

1

. Change 

power source nput cord 

2

 (sky blue) that s 

connected to 380V to the connection of 400V or 

415V.

To prevent accidents, perform the work 

after leaving the sewing machine alone 

more than 4 minutes in the state that the 

power switch is turned OFF and the power 

cord is drawn out. 

High voltage optional transformer 

1

 s set on the 

rear side of the table.
When performing changeover of voltage, remove 
transformer box 

4

 after removing top cover 

3

.

1

2

3

4

Содержание APW-896/IP-420













































































































































Отзывы:

Нет отзывов